FREE SHIPPING TO LOWER 48 STATES

Instructions for setting up a Chocolate Bomb Box with Integrated Tray

Let’s skip right to the most important part of these instructions: Fold the tray down into the box after setting up the sides. Secure the hooks on the sides before folding in the tray or there may be hassle.




With that spoiler out of the way, let’s get back to the beginning, starting with the end. Here is what a completed box should look like.




And the picture below is what a chocolate bomb box looks like fresh out of its shipping case. Lay the box on a flat surface with the inside (dull side) facing up. Begin by pre-breaking the paperboard fibers along the creases by folding the panels over 180 degrees. It is a good idea to start with the window panel scores. Pin down the window panel by pushing fingertips down on the inside window frame, right next to the fold line (try not to touch the open window-film-only area to avoid fingerprints).




Fold that thing all the way over.




After folding panels in, fold them back open and move to the next long crease line. Let’s do the crease on the other side of the window next. Use fingertips to pin down the paperboard material right next to the score on the window panel. Unfold it like the other one then move on to training the other scores.




Now, when you get to the crease that runs through the thumb hole, go ahead and fold it over then stop without unfolding it. We will do something weird with the tray panel while it is still folded in.




The tray panel gets backfolded on the crease line next to the big bomb hole(s). Bend the tray the other way: smoother-side against smoother-side with the bottom dull-side of the tray facing up. Check out the image below. Unfold it again when you are done.




Go ahead and get to pre-breaking the creases on the smaller side panels.




Get those feet on the perimeter of the holey tray too. The stubby tray feet fold down, dull-side to dull-side, conventionally, like any not-odd panel. Now is a time to check to make sure you have addressed all of the scores and not missed any. This pre-folding routine will not only make the box easier to assemble, it will also give you a more handsome structure when you are done.




Before we get to actually setting up the box, it can be a good idea to give the two long edges/creases of the lid and the bottom edge of the front panel, some special attention. You can fold over these scores and then pinch the two layers of paperboard between your fingers and carefully run down the edge, warping the paper a bit but being careful not to crinkle in it. The more these scores are tenderized, the sharper the edges of the finished box will be.




Before the next steps, it is a good idea to fold back the lid a little bit. Don’t go all the way back – just enough so it is out of the way for when you set up the sides and for later when you swing the tray into the belly of the box.




Let’s lock up the sides. Fold up the middle inside panel (the one without a hook or slot in it) so it is at 90 degrees to the bottom. With that up, fold over the panel with the #7-shaped slot. Hold the slotted-panel with one hand and grab the hooked panel with the other. Make sure the slot opening is puckered open to receive the hook.




The full body of the hook slides behind the paperboard with the hook catching behind the top of the slot from the inside. When done right, the business-end of the hook is hidden like in the picture below. Do this to both sides.




With the sides secured, now is the appropriate time to swing that tray over and inside of the box. Just make sure the feet are down at 90 degrees so they clear when you flip the tray in and so they support the tray and your spheres of yum.









Next, fold the lid wings down to 90 degrees to prepare them to slide, sandwich-meat-style, between the inner-side panel and the two panels you hooked up on the outside. While starting the wings down and in, cheat them towards the inside of the box as you lower them into the gap. Pushing them in a little as you go down will ensure you do not get snagged by the top of the hooks.




While guiding those wings in, use your thumbs to coax the lid tongue down inside front panel of the box.




Paperboard has memory and wants to spring back to flat. This can make panels pucker a bit. Dressing up the corners of the lid by pinching on the edges to take some of this memory away and make a noticeable difference in the appearance of your packaging. You can do this on the bottom front edge too if you want the sharpest box possible.




You are done! Once you get the hang of it, you will be able to fold hundreds of thousands of boxes in the time it took me to assemble these verbose instructions. Thank you for selecting BRP boxes to to provide the showcase for your cocoa bombs.
Filter Items:
4411
Case - 100
$48.36
$0.48 ea.
Pack - 10
$17.78
$1.78 ea.


4412
Case - 100
$42.66
$0.43 ea.
Pack - 10
$16.64
$1.66 ea.


4426
Case - 100
$56.54
$0.57 ea.
Pack - 10
$19.26
$1.93 ea.


4427
Case - 100
$48.22
$0.48 ea.
Pack - 10
$17.60
$1.76 ea.


4436
Case - 100
$61.94
$0.62 ea.
Pack - 10
$20.44
$2.04 ea.


4437
Case - 100
$51.40
$0.51 ea.
Pack - 10
$18.34
$1.83 ea.


4441
Case - 100
$65.76
$0.66 ea.
Pack - 10
$20.96
$2.10 ea.


4442
Case - 100
$54.24
$0.54 ea.
Pack - 10
$18.66
$1.87 ea.